Produse
Freze CNC, Laser CNC si scule
Aeromodele
   Avioane
   Zmee
Drone
Elicoptere
Gimbals/ Handhelds
Navomodele
Automodele
Vehicule electrice
Jucarii
Electronica si Roboti
Kituri de construit
Radiocomenzi
Motoare
Servomecanisme
Regulatoare pt motoare electrice
Cabluri si conectori
Acumulatori/ Incarcatori
   Baterii
Elemente de asamblare
   Diverse
Materiale de constructie
   Placaj
Materiale pentru finisaj
Diverse
   Adezivi
   Diverse
TOP

Set emitator TS832 si receptor RC832 video 5.8 GHz 600 mW

Cod RT832T
Aeromodele Echipamente FPV - UAV Sisteme de emisie/receptie audio-video Set emitator TS832 si receptor RC832 video 5.8 GHz 600 mW
Pret: 297.00 Lei
Stoc zero
Cumpara

Set emitator TS832 si receptor RC832 video 5.8 GHz 600 mW

Caracteristici:
- 40 canale: acopera benzile A, B, E si F (Airwave band)
- Doua switch-uri: buton pentru schimbarea canalelor (CH button), buton pentru schimbarea frecventei (FR button) 
- Afisaj cu doi digiti: unul pentru canal si unul pentru frecventa 
- Memorie la inchidere: memoreaza ultimul canal si ultima frecventa de lucru
- Iesire video si audio independente
 
Specificatii:
- FPV 5.8 GHz 600mW A/V Transmitting/Receiving System TS832 + RC832 - 40CH Edition | RP-SMA
- Format video: NTSC / PAL
- Conector antena: RP-SMA, jack (module side, both TX and RX) vezi diagrama de conectare
 
Specificatii TX TS832:
Tensiune alimentare: 7.4 - 16 V (3S LiPo recomandat)
Putere emisie: 600 mW
Castig antena: 2 dB
Curent absorbit: 220 mA la 12 V
Latime banda video: 8 M
Latime banda audio: 6.5 M
Masa: 22 grame
Dimensiuni: 54 x 32 x 10 mm (fara antena)
 
Specificatii RX RC832:
Tensiune alimentare: 12 V
Curent absorbit: max 200 mA
Impedanta antena: 50 Ω
Castig antena: 2 dB
Impedanta video: 75 Ω
Format video: NTSC / PAL auto
Dimensiuni:  80 x 65 x 15 mm
Masa: 85 grame
 
*Nota: Antena de emisie TX trebuie cuplata corect inainte de a cupla emitatorul la sursa de tensiune. In caz contrar dispozitivul lucreaza fara sarcina la iesire si se distruge rapid, situatie care nu este acoperita de garantia produsului.
 


 
*  We found that in recent batch, some of the TX TS-832 come with reversed power supply wires,  the first wire from left side is black instead of red, but we also noticed that for the ones with reversed wires, the wires on JST connector side are also reversed, so in this case, if you connect the JST connector to a battery pack with standard polarity JST connector, as both the sides are reversed, so the system can still work properly, but in this case, the black wire is for "Positive" pole, and the red wire is for "negative". In other words, if the first wire from left on the TX module side is black instead of red, then on JST  side, the black wire should be connected to the Positive pole of your battery.
 
The key point is that the first wire/pin from left side as shown on above diagram must be connected to "positive" pole of your power source, so if the wire color mapping is not critical for you, you can leave it without any change for the "wrong" cables,  also this TX module with wrong polarity protection, it will not damage the TX even in case the power supply is in wrong polarity. 
 
For the ones who concern about the color/polarity mapping issue too much, you can follow the below diagram to swap the wires:



 
Copyright © 2013 Sierra Modellsport Home page | Despre Sierra | Contact Site produs de Alexus Art Agency
Nume Produs:
Pretul Sierra:
Pret competitor
Website-ul competitorului