Produse
   Avioane
   Zmee
   Gimbal
   Baterii
   Diverse
   Placaj
   Airsoft
   Adezivi
   Diverse
TOP
Modul DJI NAZA-M V2 cu GPS+BEC+LED Combo Cod NAZA-M003
Drone Module de stabilizare DJI Modul DJI NAZA-M V2 cu GPS+BEC+LED Combo
Pret: 749.00 Lei - OFERTA SPECIALA
In stoc
Cumpara
NAZA-M V2 este un autopilot de mici dimensiuni pentru multicoptere, special proiectat pentru amatorii de aeromodelism. Este compact, all-in-one, are suport S-Bus, suport upgrade si port extensibil.

Diferit de WooKong-M care este destinat aplicatiilor profesionale si gestioneaza sarcini mai grele, NAZA-M V2 nu numai ca mosteneste stabilitatea de zbor remarcabila a produselor DJI, dar ofera de asemenea o manevrabilitate excelenta, care ofera pasionatilor o experienta de zbor minunata.

Modulul GPS/Compass pentru NAZA-M V2 este deja inclus in acest kit, lucru ce ofera multe functii suplimentare de zbor.

Caracteristici principale:
- Design compact
- Functii noi cu Power Management Unit (PMU) independent
- Algoritm avansat de stabilizare, cu noi imbunatatiri
- Suporta noua tipuri de platforme multicopter
- Multiple moduri de zbor/ Comutare inteligenta
- Modul GPS inclus/ Zbor la punct fix de mare acuratete
- Intelligent Orientation Control (IOC)
- Functie Failsafe imbunatatita
- Doua nivele de protectie la tensiune scazuta a acumulatorului de zbor
- Activare si dezactivare a motoarelor
- Accepta receptori PPM sau S-BUS
- Modul de semnalizare LED independent
- Hovering la punct fix chiar in conditii de vant
- Functie Return To Home
- Functie de stabilizare a camerei video implementata si operationala, cu toate reglajele necesare

Modulul de stabilizare NAZA-M V2 poate fi instalat pe orice platforma multicopter (quatro, hexa, octo).

La cerere, sistemul de stabilizare poate fi implementat si testat de catre tehnicienii nostri pe orice model de multicopter, ca solutie la cheie.
What’s difference ofNAZA‐M Lite/NAZA‐M V1/NAZA‐M V2


ALL-IN-ONE DESIGN
DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude and attitude and therefore can be used for autopilot/automatic control.

 
INDEPENDENT PMU WITH AMAZING FUNCTION EXTENSION
The Naza PMU V2 has enhanced BEC functionality and provides extendable CAN BUS ports, which can support iOSD, Zenmuse H3-2D gimbal (pitch control). Support is also included for optional Bluetooth LED module to allow parameter adjustment via a mobile APP (future firmware upgrade required for this functionality)

 
ADVANCED & IMPROVED ATTITUDE STABILIZATION ALGORITHM
The latest fourth generation attitude stabilization algorithm not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability even without the GPS module. It is more flexible and stable, and gives the hobbyists a wonderful flight experience. New features have been included such as GPS course automatic compensation, GPS & Compass sensor calibration, new take-off mode and so on.

 
NINE TYPES OF MULTI-ROTORS SUPPORTED
Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
Quad I, Quad X;
Hexa I, Hexa V, Hexa Y, Hexa IY;
Octo X, Octo I, Octo V; ( Naza-M V2 does not support the aircraft which has large vibration, so when you choose to use hexa-rotor or octo-rotor, please use the vibration dampening devices accordingly.

 
MULTIPLE FLIGHT CONTROL MODES/INTELLIGENT SWITCHING
It offers three types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. It also can adjust automatically within the flight environment and intelligently switch between GPS Atti. Mode and Atti. Mode to make sure the flight is safe and secure. In the software at the position of the manual mode you can choose manual, attitude or failsafe; it supports one key failsafe trigger.

 
GPS MODULE AVAILABLE/ACCURATE POSITION HOLD
The plug and play GPS module will greatly enhance the performance for Aerial Photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.
 

 
INTELLIGENT ORIENTATION CONTROL
Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction:
In course lock flying, the forward direction is the same as a recorded nose direction. See the following figures(Mode 1):
 
In home lock flying, the forward direction is the same as the direction from home point to multi-rotor. See the following figures (Mode 2):

 
ENHANCED FAILSAFE MODE
If your transmitter supports failsafe, then you can set failsafe through port-U. Naza controller has built-in auto level failsafe function, which means when the communication between MC and the transmitter is disconnected, the outputs of all command sticks from controller will go to center position. If the GPS module is used, you can also set RTH on failsafe. If your transmitter has only 4 channels, then MC will work in Atti. Mode by default without the failsafe function.

 
TWO LEVELS OF LOW VOLTAGE PROTECTIONS
In order to prevent your multi-rotor from crashing or other harmful consequences caused by low battery voltage, we have designed two levels of low voltage protection. You can choose not to use this, however we strongly recommend you to enable the protection. Both levels of protection have LED warning as default. The first level will blink the red light continuously; the second level will blink red light continuously and the multi-rotor will descend and land. In manual mode when low voltage protection is triggered the LED warning will be active only.
 

 
MOTOR ARM AND MOTOR DIS-ARM
There are four ways to start the motors, see the following picture:

When you want to start the multi-rotor, you need to perform any of the ways of CSC. During the flight, if the motors stop, you can immediately execute the CSC and the motors will start. This enhances the safety of the multi-rotor; no uncontrolled starting of the motors.

Motor Disarm: There are two modes of Motor Disarm: namely Intelligent Mode and Immediate Mode. For more information, please refer to the user manual or DJI Wiki.
 
Note: It has a brand new, smoother take-off algorithm, which is more stable and provides a brand-new experience in supporting double spring TX; every time you let go of the throttle stick it will hover.


 
PPM, S-BUS & ORDINARY RECEIVER SUPPORTED
Minimum Four channel receiver supported, also PPM and Futaba S-Bus receiver supported. PPM & S-Bus receivers (the general use of the first 8 channels of S-Bus receiver) to optimize the channel connection, the A, E, T, R, U five-channel functions are set using channel X2, use only one servo cable to connect the PPM or S-Bus to X2, this makes installation quick and easy.
 

 
INDEPENDENT LED MODULE
The Independent LED module makes the indication of the flight status and the system status to the ground much clearer. The pilot can get information more quickly and more conveniently, even at night, he/she can get real-time flight information feedback through the LED flashing frequency and colour. In addition, the module has a USB interface, which is used for parameter settings and firmware upgrade.
 

 
BUILT-IN GIMBAL STABILIZATION FUNCTION
The gimbal stabilization module is compatible with almost all 2-axis gimbal systems. The system will adjust the gimbal and camera according to the attitude of the aircraft after setting the parameters the first time.

 
MULTI-ROTOR ONE-POWER OUTPUT FAIL PROTECTION
In most conditions, the whole multi-rotor will retain good attitude and rotate around the frame arm with no power output, due to imbalanced mechanical structure and external environment. Rotating is mainly caused by payload and external environment. When payload is heavier, rotating speed is faster. On rotating, the hexa-rotor physical structure can cause rudder to become out of control. This humanistic protection function from Naza-M V2, in Attitude or GPS Mode, keeps attitude under control even with any one power output failed and highly reduces crash risk.

 
REMOTE GAIN ADJUSTMENT
The default parameter settings are preset for you to achieve a normal flight, and also supports remote parameter adjustment by using a control slider on the TX during flight in order to obtain better performance.

 
NEW ASSISTANT SOFTWARE & FIRMWARE ONLINE UPDATE
The user interface of the assistant software has been comprehensively updated and brings you a new interaction experience. Instructions will automatically appear which is very convenient. In addition, on the left side of each menu section there is additional information. The logical design makes your parameter settings more simple and convenient. Like other DJI products the Naza-M V2 firmware can be upgraded free online.



Technical Specifications:

Continutul kit-ului:
- Modul de stabilizare NAZA-M V2
- Modul BEC + Modul LED + Modul GPS
- Cablu interfata USB
- 8x Cabluri cu conectori servo
- 2x Banda adeziva
- Instructiuni click aici


















 

Produse Asociate
Piese de schimb
Copyright © 2013 Sierra Modellsport Home page | Despre Sierra | Contact Site produs de Alexus Art Agency
Nume Produs:
Pretul Sierra:
Pret competitor
Website-ul competitorului